My watch list
my.chemeurope.com  
Login  

Ohm




 

 

The ohm (symbol: Ω) is the SI unit of electrical impedance or, in the direct current case, electrical resistance, named after Georg Ohm.

Contents

Definition

An ohm is the electrical resistance offered by a current-carrying element that produces a voltage drop of one volt when a current of one ampere is flowing through it.

\Omega = \dfrac{\mbox{V}}{\mbox{A}} = \dfrac{\mbox{m}^2 \cdot \mbox{kg}}{\mbox{s}^{3} \cdot \mbox{A}^2}

Explanation

 

By definition from Ohm's Law, a device has a resistance of one ohm if a voltage of one volt causes a current of one ampere to flow (R = V/I). Alternatively and equivalently, a device that dissipates one watt of power with one ampere of current flowing through it has a resistance of one ohm (R = P / I 2).

Since 1990, the ohm has been maintained internationally using the quantum Hall effect, where a conventional value is used for the 'von-Klitzing constant', fixed by the 18th General Conference on Weights and Measures as R{K-90} = 25812.807 Ω.

The complex quantity impedance is a generalisation of resistance. Its real part is resistance and its imaginary part is reactance. Impedance, resistance and reactance all have units of ohms.

The symbol for the ohm is the Greek capital letter omega (Ω). If the Greek letter cannot be used, the word ohm is used instead. The various guides for the use of the International System of Units do not explicitly forbid the elision of the final "o" of some SI prefixes, although there is nothing in them to suggest that it is allowable, either. As a result, one is just about as likely to see "kilohm", "kiloohm" and even "kilo-ohm", and the same holds true for hecto-, micro-, nano-, pico-, femto-, atto-, zepto-, and yocto-. The only other SI unit to suffer from this kind of orthographic uncertainty is the ampere. In the particular case of the ohm, one even sees the "a" prefixes lose that vowel: hence megohm and gigohm. Higher prefixes are rarely used with ohm. In the other direction, milliohms (or millohms) are seen where the resistance of cables, etc., are measured.

Units of ohms, kilohms (103 Ω) and megohms (106 Ω) are used in electronic design documentation. On schematic diagrams and parts lists kilohms are abbreviated "K" and megohms are abbreviated "M". Thus, 33 kilohms would be rendered as 33K, and 5.1 megohms would be 5.1M. Another commonly used convention is that the multiplier is used to replace the decimal point, so that 5.1 megohms can also be represented as 5M1. This convention is used because a decimal point can be difficult to see in small or cluttered print. Values less than 1K are rendered either (a) without any symbol, or (b) with an "R", following the number; so 680 ohms can be shown as 680 or 680R, and 4.7 ohms as 4R7. Resistors are usually identified by a reference designator, R, and a cardinal number, e.g., R12.

This SI unit is named after Georg Ohm. As with all SI units whose names are derived from the proper name of a person, the first letter of its symbol is uppercase (Ω). But when an SI unit is spelled out, it should always be written in lowercase (ohm), unless it begins a sentence or is the name "degree Celsius".
— Based on The International System of Units, section 5.2.

Conversions

  • A measurement in ohms is the reciprocal of a measurement in siemens, the SI unit of electrical conductance. Note that 'siemens' is both singular and plural. The non-SI unit, the mho (ohm written backwards), is equivalent to siemens but is mostly obsolete and rarely used.
  • Ohms to watts: The power dissipated by a resistor may be calculated using resistance and voltage. The formula is a combination of Ohm's law and Joule's law:
P={V^2 \over R}
where P is the power in watts, R is the resistance in ohms and V is the voltage across the resistor.
This method is not reliable for determining the power of an incandescent light bulb, resistance heater or electric short since all these devices operate at high temperatures and the resistance measured using a meter will not represent the operating resistance. For these conditions instead multiply V by current in amperes to get power in watts.

See also

  • Ohm's law
  • Resistor
  • abohm
 
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article "Ohm". A list of authors is available in Wikipedia.
Your browser is not current. Microsoft Internet Explorer 6.0 does not support some functions on Chemie.DE