My watch list
my.chemeurope.com  
Login  

Amine gas treating



Amine gas treating refers to a group of processes that use aqueous solutions of various amines to remove hydrogen sulfide (H2S) and carbon dioxide (CO2) from gases. It is a common unit process used in refineries, petrochemical plants, natural gas processing plants and other industries. The process is also known as Acid gas removal and Gas sweetening.

Processes within oil refineries or natural gas processing plants that remove hydrogen sulfide and/or mercaptans are commonly referred to as sweetening processes because they results in products which no longer have the sour, foul odors of mercaptans and hydrogen sulfide.

There are many different amines used in gas treating:

  • Monoethanolamine (MEA)
  • Diethanolamine (DEA)
  • Methyldiethanolamine (MDEA)
  • Diisopropylamine (DIPA)
  • Diglycolamine (DGA)

The most commonly used amines in industrial plants are the alkanolamines MEA, DEA, and MDEA.

Amines are also used in many oil refineries to remove sour gases from liquid hydrocarbons such as liquified petroleum gas (LPG).

Contents

Description of a typical amine treater

Gases containing H2S or both H2S and CO2 are commonly referred to as sour gases or acid gases in the hydrocarbon processing industries.

A typical amine gas treating process (as shown in the flow diagram below) includes an absorber unit and a regenerator unit as well as accessory equipment. In the absorber, the downflowing amine solution absorbs H2S and CO2 from the upflowing sour gas to produce a sweetened gas stream (i.e., an H2S-free gas) as a product and an amine solution rich in the absorbed acid gases. The resultant "rich" amine is then routed into the regenerator (a stripper with a reboiler) to produce regenerated or "lean" amine that is recycled for reuse in the absorber. The stripped overhead gas from the regenerator is concentrated H2S and CO2. In oil refineries, that stripped gas is mostly H2S, much of which often comes from a sulfur-removing process called hydrodesulfurization. This H2S-rich stripped gas stream is then usually routed into a Claus process to convert it into elemental sulfur. In fact, the vast majority of the 64,000,000 metric tons of sulfur produced worldwide in 2005 was byproduct sulfur from refineries and other hydrocarbon processing plants. [1][2] In some plants, more than one amine absorber unit may share a common regenerator unit.

 

In the steam reforming process of hydrocarbons to produce gaseous hydrogen for subsequent use in the industrial synthesis of ammonia, amine treating is one of the commonly used processes for removing excess carbon dioxide in the final purification of the gaseous hydrogen.

New amine-based materials for gas processing

In recent years, interest in the development of new materials and technologies for the 'capture' of carbon dioxide (CO2) has increased significantly. This development appears to be driven largely by increasing concerns about the impact of rising CO2 emissions on climate change (specifically global warming). One outcome has been the introduction of new reactive amines which have chemical structures in which the CO2-reactive part of the molecule (the amine group) is tethered to an ionic (salt-like) structural element. The ionic nature of these hybrids makes them less likely to be lost to evaporation during CO2 capture operations, and as a result it may be possible to suppress the typical amine loss in scrubbing systems of about four pounds of amine per ton of CO2 captured. While systems involving the use of certain simple amine-salt solutions in water were first evaluated for CO2 capture decades ago, it was only in 2002 [3] that systems of pure, CO2-reactive liquid salts (amine-appended task-specific ionic liquids called TSILs) were first introduced. Recently, the researchers responsible for that development have reported improved approaches[4] (e.g., the use of Click chemistry and commodity chemicals) for the preparation of CO2-reactive salts, procedures which result in salts that are much less expensive to prepare than the earlier first-generation of materials. Interestingly, the library of new compounds obtained in this fashion also included CO2-reactive salts that are plastic-, resin- and gel-like in character.

See also

References

  1. ^ Sulfur production report by the United States Geological Survey
  2. ^ Discussion of recovered byproduct sulfur
  3. ^ Bates, E. D.; Mayton, R. D.; Ntai, I.; Davis, J. H., Jr., CO2 Capture by a Task-Specific Ionic Liquid, Journal of the American Chemical Society, 2002, Vol. 124, No. 6, 926-927
  4. ^ Soutullo, M. D.; Odom, C. I.; Wicker, B. F.; Henderson, C. N.; Stenson, A. C.; Davis, J. H., Jr., Reversible CO2 Capture by Unexpected Plastic-, Resin, and Gel-like Ionic Soft Materials Discovered During the Combi-Click Generation of a TSIL Library, Chemistry of Materials, 2007, Vol. 19, No. 15, 3581-3583
  • Natural Gas Supply Association Scroll down to Sulfur and Carbon Dioxide Removal
  • Sweetening LPG's with Amines, Holmes, J.W. (Bryan Research & Engineering), Spears, M.L. (Bryan Research & Engineering), and Bullin, J.A. (Texas A&M University), Chemical Engineering Progress, May 1984
  • Description of the classic book on gas treating by Arthur Kohl & Richard Nielsen. Gas Purification, Fifth Edition, Gulf Publishing. ISBN 0-88415-2200. 
 
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article "Amine_gas_treating". A list of authors is available in Wikipedia.
Your browser is not current. Microsoft Internet Explorer 6.0 does not support some functions on Chemie.DE