My watch list
my.chemeurope.com  
Login  

Claus process



The Claus process is the most significant gas desulfurizing process, recovering elemental sulfur from gaseous hydrogen sulfide. First invented over 100 years ago, the Claus process has become the industry standard. The multi-step process recovers sulfur from the gaseous hydrogen sulfide found in raw natural gas and from the by-product gases containing hydrogen sulfide derived from refining crude oil and other industrial processes. The final step involves oxidation of the hydrogen sulfide.

Gases with a H2S content of over 25%[citation needed] are suitable for the recovery of sulfur in Claus plants. These gases may also contain hydrogen cyanide, hydrocarbons, sulfur dioxide or ammonia. They mainly originate from physical and chemical gas treatment units (Selexol, Rectisol, Purisol and amine scrubbers) in refineries, natural gas processing plants and gasification or synthesis gas plants. The sulfur recovered in Claus plants is used for manufacturing sulfuric acid, medicine, cosmetics, fertilizers and rubber products.

Hydrogen sulfide produced, for example, in the hydrodesulfurization of refinery naphthas and other petroleum oils, is converted to sulfur in Claus plants.[1] The overall main reaction equation is:

2H2S + O2 → S2 + 2H2O

In fact, the vast majority of the 64,000,000 metric tons of sulfur produced worldwide in 2005 was byproduct sulfur from refineries and other hydrocarbon processing plants.[2][3]

Additional recommended knowledge

Contents

History

The process was invented by Carl Friedrich Claus, a chemist working in England. A British patent was issued to him in 1883. The process was later significantly modified by a German company called I.G.Farbenindustrie A.G.[4]

Process description

A schematic process flow diagram of a basic Claus process unit is shown below:[5]



The Claus technology can be divided into two process steps, thermal and catalytic.

In the thermal step, hydrogen sulfide-laden gas reacts in a substoichiometric combustion at temperatures above 850 °C such that elemental sulfur precipitates in the downstream process gas cooler.

The H2S-content and the concentration of other combustible components (hydrocarbons or ammonia) determine the location where the feed gas is burned. Claus gases (acid gas) with no further combustible contents apart from H2S are burned in lances surrounding a central muffle by the following chemical reaction:

2H2S + 3O2 → 2SO2 + 2H2O

Gases containing ammonia, such as the gas from the refinery's sour water stripper (SWS), or hydrocarbons are converted in the burner muffle. Sufficient air is injected into the muffle for the complete combustion of all hydrocarbons and ammonia. Air to the acid gas is controlled such that in total 1/3 of all hydrogen sulfide (H2S) is converted to SO2. This ensures a stoichiometric reaction for the Claus reaction (see next section below).

The separation of the combustion processes ensures an accurate dosage of the required air volume needed as a function of the feed gas composition. To reduce the process gas volume or obtain higher combustion temperatures, the air requirement can also be covered by injecting pure oxygen. Several technologies utilizing high-level and low-level oxygen enrichment are available in industry, which requires the use of a special burner in the reaction furnace for this process option.

Usually, 60 to 70% of the total amount of elemental sulfur produced in the process are obtained in the thermal process step.

The main portion of the hot gas from the combustion chamber flows through the tube of the process gas cooler and is cooled down such that the sulfur formed in the reaction step condenses. The heat given off by the process gas and the condensation heat evolved are utilized to produce medium or low-pressure steam. The condensed sulfur is removed at the gas outlet section of the process gas cooler.

A small portion of the process gas can be routed through a bypass inside of the process gas cooler, as depicted in the figure. This hot bypass stream is added to the cold process gas through a three-way valve to adjust the inlet temperature required for the first reactor.

Catalytic step

The Claus reaction continues in the catalytic step with activated alumina or titanium dioxide, and serves to boost the sulfur yield. The hydrogen sulfide (H2S) reacts with the SO2 formed during combustion in the reaction furnace, and results in gaseous, elemental sulfur. This is called the Claus reaction:

2H2S + SO2 → 3S + 2H2O

The catalytic recovery of sulfur consists of three substeps: heating, catalytic reaction and cooling plus condensation. These three steps are normally repeated a maximum of three times. Where an incineration or tail-gas treatment unit (TGTU) is added downstream of the Claus plant, only two catalytic stages are usually installed.

The first process step in the catalytic stage is the process gas heating. It is necessary to prevent sulfur condensation in the catalyst bed, which can lead to catalyst fouling. The required bed operating temperature in the individual catalytic stages is achieved by heating the process gas in a reheater until the desired operating bed temperature is reached.

Several methods of reheating are used in industry:

  • Hotgas bypass: which involves mixing the two process gas streams from the process gas cooler (cold gas) and the bypass (hot gas) from the first pass of the Wasteheat boiler.
  • Indirect Steam reheaters: the gas can also be heated with high pressure steam in a heat exchanger.
  • Gas/Gas Exchangers: whereby the cooled gas from the process gas cooler is indirectly heated from the hot gas coming out of an upstream catalytic reactor in a gas-to-gas exchanger.
  • Direct-fired Heaters: fired reheaters utilizing acid gas or fuel gas, which is burned substoichiometrically to avoid oxygen breakthrough with can damage Claus catalyst.

The typically recommended operating temperature of the first catalyst stage is 315°C to 330°C (bottom bed temperature). The high temperature in the first stage also helps to hydrolyze COS and CS2, which is formed in the furnace and would not otherwise be converted in the modified Claus process.

The catalytic conversion is maximized at lower temperatures, but care must be taken to ensure that each bed is operated above the dewpoint of sulfur. The operating temperatures of the subsequent catalytic stages are typically 240°C for the second stage and 200°C for the third stage (bottom bed temperatures).

In the sulfur condenser, the process gas coming from the catalytic reactor is cooled to between 150 and 130°C. The condensation heat is used to generate steam at the shell side of the condenser.

Before storage, liquid sulfur streams from the process gas cooler, the sulfur condensers and from the final sulfur separator are routed to the degassing unit, where the gases (primarily H2S) dissolved in the sulfur are removed.

The tail gas from the Claus process still containing combustible components and sulfur compounds (H2S, H2 and CO) is either burned in an incineration unit or further desulfurized in a downstream tail gas treatment unit.

Process performance

Using two catalytic stages, the process will typically yield over 97% of the sulfur in the input stream. Over 2.6 tons of steam will be generated for each ton of sulfur yield.

See also

References

  1. ^ Gary, J.H. and Handwerk, G.E. (1984). Petroleum Refining Technology and Economics, 2nd Edition, Marcel Dekker, Inc.. 0824771508. 
  2. ^ Sulfur production report by the United States Geological Survey
  3. ^ Discussion of recovered byproduct sulfur
  4. ^ Bibliographic Citation
  5. ^ A publication of the Linde Gas Division of the Linde Group
 
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article "Claus_process". A list of authors is available in Wikipedia.
Your browser is not current. Microsoft Internet Explorer 6.0 does not support some functions on Chemie.DE